Ansi A117 1 2012 Accessibility Standards



ASTM c90

ASTM c90

...date. 1. Scope 1.1 This specification covers hollow and solid (see 5.3 and 5.4) concrete masonry units made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. There are three classes of concrete masonry units: (1) normal weight, (2) medium weight, and (3)...

ASTM a126

ASTM a126

...not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers three classes of gray iron for castings intended for use as valve pressure retaining parts, pipe fittings, and flanges....

ASTM c270

ASTM c270

...does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers mortars for use in the construction of non-reinforced and reinforced unit masonry structures. Four types of mortar are...

ASTM d 698

ASTM d 698

...compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors. 1. Scope 1.1 These test methods cover laboratory compaction methods used to determine the relationship between molding water content and dry...

ASTM a148

ASTM a148

...not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date....

ASTM a 276

ASTM a 276

...and users of cemented carbides.   1. Scope 1.1 This test method specifies procedures for the metallographic determination of apparent porosity in cemented carbides. Note 1—The term “apparent porosity” is construed to mean all microstructures observed on a properly prepared, unetched surface, including structures resulting from uncombined carbon, non-metallic...

ASTM d3039

ASTM d3039

...volume percent reinforcement. Properties, in the test direction, which may be obtained from this test method include the following:   Ultimate tensile strength, Ultimate tensile strain, Tensile chord modulus of elasticity, Poisson’s ratio, and Transition strain. 1. Scope 1.1 This test method determines the in-plane tensile properties of polymer...

ASTM d2321

ASTM d2321

...given in Appendix X2.   1. Scope 1.1 This practice provides recommendations for the installation of buried thermoplastic pipe used in sewers and other gravity-flow applications. These recommendations are intended to ensure a stable underground environment for thermoplastic pipe under a wide range of service conditions. However, because of...

ASTM f88

ASTM f88

...of fixtures and techniques are illustrated in Fig. 1. Technique A: Unsupported—Each tail of the specimen is secured in opposing grips and the seal remains unsupported while the test is being conducted. Technique B: Supported 90° (By Hand)—Each tail of the specimen is secured in opposing grips and the...

ASTM e399

ASTM e399

...to the expected loading and environment, and in relation to the sensitivity and reliability of the crack detection procedures that are to be applied prior to service and subsequently during the anticipated life. 1. Scope 1.1 This test method covers the determination of fracture toughness (KIc) of metallic materials...

ACCESSIBILITY CHEAT SHEET KEY CODES: ICC/ANSI A117

ACCESSIBILITY CHEAT SHEET . KEY CODES: ICC/ANSI A117.1 – Defines accessibility. Typically 2003 version used, however was updated in 2009. • 2003 version allows ...

ANSI-American National Standards Institute

American National Standards Institute is a premier source for timely, relevant, actionable information on national, regional, international standards and conformity ...

ANSI WebStore - American National Standards

Download international and US standards from the full collections of ISO and IEC standards, American National Standards and thousands of regional and foreign standards

Differences Between Accessibility Requirements found in ...

Differences Between Accessibility Requirements found in the International Building Code/ICC ANSI A117.1 and the 2010 ADA Standards: Problem Areas for Compliance

ICC A117.1-2009 Standard and Commentary: Accessible and ...

Store > ICC A117.1-2009 Standard and Commentary: Accessible and Usable Buildings and Facilities

ANSI: American National Standards Institute

ANSI B77.1-2011 and ANSI B77.1a-2012 Revises ANSI B77.1-2006 Passenger Ropeways - Aerial Tramways, Aerial Lifts, Surface Lifts, Tows and Conveyors - Safety Requirements

ICC A117.1-2009 Accessible and Usable Buildings and Facilities

Front Matter (Title Page, TOC, and Forward) Sample Pages. The specifications in this standard make sites, facilities, buildings and elements accessible to and usable ...

ICC (ASC A117) | ICC - iccsafe.org

The 2017* edition of ICC A117.1 entitled Standard for Accessible and Usable Buildings and Facilities was approved by ANSI as an American National Standard on March 28 ...

ANSI A117.1 2003. Section 604. Ambulatory Accessible ...

1 ANSI A117.1 2003. Section 604. Ambulatory Accessible Compartments. 2005 CSBC. 1109.2.2 Water closet compartment. Where water closet compartments are provided in a ...

Free PDFs - International Building Code, ADA and More!

Free! and all in one place; a list of PDFs for popular building codes & accessibility standards; 2015 IBC, 2013 CBC, NFPA 101, ADA, FHA, ANSI A117.1 & more!