Ansi A117 1 2012 Accessibility Standards



ASTM c136

ASTM c136

...determination of material finer than the 75-μm (No. 200) sieve cannot be achieved by use of this test method alone. Test Method C 117 for material finer than 75-μm sieve by washing should be employed. Refer to methods of sampling and testing in Specification C 637 for heavyweight aggregates....

ASTM e1527-05

ASTM e1527-05

...commercial real estate may necessitate investigation beyond that identified in this practice (see Sections 1.3 and 13).   1.1.1 Recognized Environmental ConditionsIn defining a standard of good commercial and customary practice for conducting an environmental site assessment of a parcel of property, the goal of the processes established by...

ASTM a313

ASTM a313

...with the standard. 1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units. 2. Referenced Documents (purchase separately) ASTM Standards A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire Rods A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel...

ASTM d4052

ASTM d4052

...characterize both the light and heavy fractions of petroleum and petroleum products.   Determination of the density or relative density of petroleum and its products is necessary for the conversion of measured volumes to volumes at the standard temperature of 15°C. 1. Scope 1.1 This test method covers the...

ASTM a388

ASTM a388

...a combination thereof, which give rise to ultrasonic indications. The ultrasonic quality level shall be clearly stated as order requirements. 1. Scope 1.1 This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of steel forgings by the straight and angle-beam techniques. The straight beam techniques include...

ASTM c143

ASTM c143

...cohesive for this test to have significance. Caution should be exercised in interpreting such results. 1. Scope 1.1 This test method covers determination of slump of hydraulic-cement concrete, both in the laboratory and in the field. 1.2 The values stated in either SI units or inch-pound units are to...

ASTM a182 f316

ASTM a182 f316

...not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers one grade of ferrovanadium. 1.2 The values stated in inch-pound units are to be regarded as standard. The values...

ASTM d 2487

ASTM d 2487

...does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This practice covers the proper methods of installing vitrified clay pipe lines in order to fully utilize the structural properties of...

ASTM c 840

ASTM c 840

...for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers the requirements for electrodeposited zinc cobalt alloy coatings on metals. 1.2 The...

ASTM d 882

ASTM d 882

...(less than 1.0 mm (0.04 in.) in thickness).   Note 1—Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.). Note 2—Tensile properties of plastics 1.0 mm (0.04 in.) or greater in thickness shall be determined according to Test Method D 638....

The 2010 ADA Standard for Accessible Design/2012 ...

2010 ADA/2012 IBC/2009 ICC A117.1 Comparison Page 1 of 330 The 2010 ADA Standard for Accessible Design/2012 International Build-ing Code with 2009 ICC A117.1 ...

ANSI-American National Standards Institute

American National Standards Institute is a premier source for timely, relevant, actionable information on national, regional, international standards and conformity ...

ACCESSIBILITY CHEAT SHEET KEY CODES: ICC/ANSI A117

ACCESSIBILITY CHEAT SHEET . KEY CODES: ICC/ANSI A117.1 – Defines accessibility. Typically 2003 version used, however was updated in 2009. • 2003 version allows ...

ANSI WebStore - American National Standards

On the webstore, you can obtain U.S. and international standards… Search for standards from ANSI, ISO, IEC, ASTM and other standards publishers by keyword or ...

ICC A117.1-2009 Standard and Commentary: Accessible and ...

Store > ICC A117.1-2009 Standard and Commentary: Accessible and Usable Buildings and Facilities

ANSI: American National Standards Institute

ANSI B77.1-2011 and ANSI B77.1a-2012 Revises ANSI B77.1-2006 Passenger Ropeways - Aerial Tramways, Aerial Lifts, Surface Lifts, Tows and Conveyors - Safety Requirements

ICC A117.1 Accessible and Usable Buildings and Facilities

Front Matter (Title Page, TOC, and Forward) Sample Pages. The specifications in this standard make sites, facilities, buildings and elements accessible to and usable ...

Accessibility Info | ICC - iccsafe.org

Improving the Accessibility of Buildings for People with Disabilities. The odds are that many of us will experience a disability at some point in our lives.

ANSI/ASSE A1264.2-2012

6 o surfaces. New York: American National Standards Institute. ANSI/ ASSE A1264.2-20061 [www.ansi.org]. ANSI [2007]. Safety ... www.cdc.gov/niosh/docs/2011-123/pdfs ...

ICC/ANSI A117.1-2003 Countertop and Cabinet Depth | Int'l ...

Tom, A commercial kitchen is a work space. The ANSI states how to build it but not when it is requried. Both the IBC and 2010 ADA Standards exempt work areas from ...