ASTM A320-08

ASTM A320-08, ASTM A320-08 pdf, ASTM A320-08 download, ASTM A320-08 download pdf, download ASTM A320-08, free download ASTM A320-08, ASTM A320-08 free download

ASTM A320-08 pdf free download

ASTM A320-08 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for Low-Temperature Service
ASTM International / 15-Mar-2008 / 8 pages ASTM A320-08 pdf

1.1 This ASTM A320-08 specification covers alloy steel bolting materials for pressure vessels, valves, flanges, and fittings for low-temperature service. The term “bolting material” as used in this specification covers rolled, forged, or strain hardened bars, bolts, screws, studs, and stud bolts. The bars shall be hot-wrought.

The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood.1.2 Several grades are covered, including both ferritic and austenitic steels designated L7, B8, etc. Selection will depend on design, service conditions, mechanical properties, and low-temperature characteristics.

The mechanical requirements of Table 1 indicate the diameters for which the minimum mechanical properties apply to the various grades and classes, and Table 2 stipulates the requirements for Charpy impact energy absorption. ASTM A320-08, The manufacturer should determine that the material can conform to these requirements before parts are manufactured. For example, when Grade L43 is specified to meet the Table 2 impact energy values at ??150 °F [??101 °C], additional restrictions (such as procuring a steel with lower P and S contents than might normally be supplied) in the chemical composition for AISI 4340 are likely to be required. Note 1 – The committee formulating this specification has included several grades of material that have been rather extensively used for the present purpose.

Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent. Users should note that hardenability of some of the grades mentioned may restrict the maximum size at which the required mechanical properties are obtainable. 1.3 Nuts for use with this bolting material are covered in Section 10 and the nut material shall be impact tested. 1.4 Supplementary Requirements (S1, S2, and S3) of an optional nature are provided. They shall apply only when specified in the inquiry, contract and order. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. ASTM A320-08, Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Keywords ASTM A320-08 : additional elements; austenitic stainless steel; bolts—steel; chromium-molybdenum steel; fasteners—steel; markings on fittings; nickel-chromium-molybdenum alloy steel; pressure vessel service; stainless steel bolting material; starting material; steel bars—alloy; steel bolting material; steel flanges; steel valves; temperature service applications—low; Alloy steel bars–specifications; Alloy steel bolting materials–specifications; Austenitic steel–specifications; Low-temperature service applications–steel; Stainless steel bolting materials–specifications; Steel fittings–specifications; Steel flanges–specifications; Steel valves–specifications; ICS Number Code 21.060.01 (Fasteners in general); 77.080.20 (Steels), ASTM A320-08.

File Type Download : PDF File, ASTM A320-08



K-12 MODULE IN VALUES GRADE 9, PLATE charpy v notch FOR PLATES 673 v aisc 360, a320 bolts vs a325, DEPED OHSP VALUES ED MODULES, grade 9 values education module, PLATE charpy v notch 673 v aisc 360, module 8 edukasyong pagpapakatao, modules in edukasyon sa pagpapakatao, stud bolts pre heat requirements